Vizio XMF1000 User Manual

XMF1000 - QUICK INSTALL GUIDEQUICK INSTALL SLIM HDTV MOUNT UNIVERSAL FOR 32” - 55” TVS UP TO 100 LBS

89. Remove 2 lag bolts and 2 washers from the pouch labeled LAG. Use a wrench to insert the lag bolts and washers as shown. Tighten

OPTIONAL: The extender can be attached to lengthen the bar. A longer bar may be easier to access when mounting large TVs. To attach the ex

1STEP 3B - MOUNTING TO A CONCRETE WALL1. Determine the height at which you want the mount to hang. Mark the position of the left bracket hole wit

1143. Remove 1 lag bolt and 1 washer from the pouch labeled LAG. Place a bracket (part A) against the wall as shown, and use a wrench t

5. Remove the bar, the leveler, and the unattached bracket (part A) from the wall. Allow the attached bracket to swing down. Using the powe

77. Remove 3 lag bolts and 3 washers from the pouch labeled LAG. Place the other bracket (part A) against the wall as shown, and use a

1499. Attach the handle (part F) to the end of the bar. Secure the handle to the bar by inserting a screw (part H) into the bottom hole on th

STEP 4 - ATTACHING THE TV HOOKS AND KICK STANDS1. Gently place the TV on the floor screen-down. You may want to place a rug or blanket beneath the

OPTIONAL: If you want your TV to have a 9° downward tilt when mounted, use the spacers (part G) and the longer screws when mounting the

4. Place the two kickstands (parts C and D) against the two bottom mounting holes as shown. The larger kickstand can be placed on either the l

IMPORTANT SAFETY INFORMATIONRead the Important Safety Information on this page before installing or using this mounting system.Always follow the instr

STEP 5 - HANGING THE TV ON THE MOUNT1. Turn the handle on the bar until the flat side of the bar is facing the wall. 2. With the help of anot

33. Turn the handle on the bar until the flat side of the bar is facing down. Ensure the flat side of the bar is facing down. This locks the

TECHNICAL SUPPORTProducts are often returned due to a technical problem rather than a defective product that may result in unnecessary shipping charge

ONE-YEAR LIMITED WARRANTY & INSURANCECovers units purchased as new in United States and Puerto Rico Only VIZIO warrants for a period of one (1) ye

TRADEMARKS SHOWN ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. IMAGES USED ARE FOR ILLUSTRATION PURPOSES ONLY. VIZIO, THE V LOGO, WHERE VISION MEETS VA

STEP 1 - BEFORE YOU BEGINYOU WILL NEEDPower Drill 1/2” (12.7mm) Concrete Drill Bit 7/32” (5.5mm) Drill BitPencil Electronic Stud FinderPhillips-head S

STEP 2 - REVIEW THE PACKAGE CONTENTSBefore you begin, ensure all parts are included and undamaged. To prevent loss, do not unpack the small parts unti

3x 2M8x 4x 2M4x 4x 2M5x 4x 2M6x 4LAGx 4 x 4ANCHORx 4x 4MISCx 4[ M4 x 44 ] [ M4 x 15 ][ M5 x 44 ] [ M5 x 15 ][ M6 x 44 ] [ M6 x 15 ][ M8 x 48 ] [ M8 x

STEP 3A - MOUNTING TO A WALL WITH WOOD STUDSThe mount can be attached to walls with wood studs. The wall covering (drywall, lath, plaster, etc.) may n

43. Remove 1 lag bolt and 1 washer from the pouch labeled LAG. Place part A against the wall as shown, and use a wrench to insert the l

5. Remove the bar, the leveler, and the unattached bracket (part A) from the wall. Using the power drill and the 7/32” drill bit, drill into th

7. Push the bar through the openings in each bracket (part A) as shown. Snap on the leveler (part E) and verify that the bar is level. Make